Frequency Range (-10 dB) |
52 Hz – 210 Hz |
Frequency Response (±3 dB) |
62 Hz – 123 kHz |
System Power Rating |
1600 W Continuous Pink Noise (6400 W peak), 2 hrs800 W Continuous Pink Noise (3200W peak), 100 hrs |
Maximum Input Voltage |
80 V Rms (2 hrs), 160 V peak |
Maximum SPL (1m) |
127 dB Cont. Ave (2 hrs), 133 dB Peak |
Sensitivity |
98 dB (52 Hz – 210 Hz, 2.83V) |
Impedance |
4Ω, 3.0Ω min @ 195 Hz |
Amplifiers |
Crown DCi Family with DSP on-board |
Recommended |
Crown DCi 2 | 2400N Crown DCi 4 | 2400N |
Low Frequency Driver |
2 x 2275H, 304 mm (15 in) diameter , each with two 76 mm (3 in) diameter voice coils, Neodymium Differential Drive®, Direct Cooled™ |
Enclosure Material |
Fiberglass shell, gelcoat finish, with 18 mm Birch plywood internal bracing. |
Grille |
Powder coated 14 gauge hex-perforated steel with zinc under-coating, backed with acoustically transparent cloth and hydrophobic screen. |
Inter-Enclosure Angles |
VLA-C125S to VLA-C125S: 0° using VLA-C125S Bracket Plate (included with VLA-C125S)VLA-C265 below VLA-C125S Subwoofer (VLA-C265 cannot be connected above C125S): 0°, 5° using VLA-C125S Bracket Plate (included with VLA-C125S)VLA-C2100 below VLA-C125S Subwoofer (VLA-C2100 cannot be connected above C125S): 0°, 7.5° using VLA-C125S Bracket Plate (included with VLA-C125S) |
Environmental |
IP-55 rating per IEC529 (dust protected and protected against jets of water). |
Terminals |
CE-compliant covered barrier strip terminals. Barrier terminals accept up to 5.2 sq mm (10 AWG) wire or max width 9mm (0.375 in) spade lugs. Touch-proof covers. Full set of terminals on back panel, plus optional-use inter-cabinet connection terminals located on top and bottom panels of cabinet. |
Colors |
-GR: Gray (similar to Pantone 428C), -BK: Black |
Dimensions (H x W x D) |
508 x 848 x 634 mm (20.0 x 33.4 x 24.9 in) |
Net Weight (ea) |
56.7 kg (125 lbs) |
Shipping Weight (ea) |
62.6 kg (138 lbs) |
Included Accessories |
2 x VLA-C125S Bracket Plates 8 pcs. M10 x 35 mm stainless steel bolts (1.5mm pitch, 6 mm hex-drive) for attaching Bracket Plates 2 pcs. Plastic Trim Cover Panels for Bracket Plates, each attaches via 4 pcs (8 total) 3-32 x ½” trusshead, phillips-drive, stainless steel bolts. |
Optional Accessories |
VLA-C-SB Suspension Bar Kit -- For top & bottom of the array, includes 2 identical Suspension Bars (for top/bottom), 4 pcs ¾-inch Class 2 Screw Pin Shackles (must use 2 Shackles for each Suspension Bar, located at end channels, not in the center).VLA-C125S-ACC kit – For adding terminal cup to front to allow easy and neat cardioid subwoofer wiring. VLA-C-ACC kit – For adding front baffle terminals for cardioid subwoofer configuration. |